Brand: SuperPro
Replacement parts compatible with SuperPro
60 parts
- Matched to OEM specs
- Batch-tested quality
- Verified cross-references
POOLPOINT is an independent manufacturer. Not affiliated with, endorsed by or sponsored by SuperPro. Brand names indicate fitment only.
Shop SuperPro parts by category
60 parts
View all 60
Fits SuperPro
D.E. Filter Grid, 24 Sq Ft, Small, Compatible with SuperPro
Fits SuperPro
D.E. Filter Grid, 24 Sq Ft, Large, Compatible with SuperPro
Fits SuperPro
O-Ring, 6-3/4-Inch ID, 3/16-Inch, Compatible with Jandy SFTM Top Mount Valves
Fits SuperPro
Pump Basket, Compatible with Hayward Super Pump SPX1600M
Fits SuperPro
O-Ring, 15-1/4-Inch ID, 3/8-Inch Cross Section, for PLM Filters
Fits SuperPro
Pump Basket for Challenger Pumps, Compatible with Pentair
Fits SuperPro
Multiport Valve Rebuild Kit, 2-Inch, Replacement for Pentair 261055 and SM-20-2 Valves
Fits SuperPro
Diverter Spider Gasket, 2-Inch, Replacement for Pentair PacFab Backwash Valves
Fits SuperPro
O-Ring, 4-3/4-Inch ID, 3/32-Inch Cross Section for Flo-Master Pumps
Fits SuperPro
DE Filter Grid, 48 Sq Ft, 24-Inch, Compatible with SuperPro Filters
Sourcing SuperPro-compatible parts in bulk
An aftermarket SuperPro-compatible part is manufactured to the same critical dimensions as the original but is not made by SuperPro. We check every part against an OEM sample for thread pitch, port geometry and sealing surfaces before tooling is approved, so it installs without modification.
SuperPro numbers typically carry prefixes such as SP, SPX, DG, PG — the number is usually molded into the part or printed on the equipment label. Enter it above to find cross-referenced replacements.
Before committing to a container, distributors should confirm fitment by OEM number, equipment model, and thread or port size. We supply photos, dimensional drawings and, on key parts, 3D models — plus samples for validation ahead of bulk production.
FAQ
Are these genuine SuperPro parts?
No. We manufacture compatible aftermarket replacements. SuperPro OEM numbers are listed to identify fitment only, and we are not affiliated with SuperPro.
Do you supply BSP threads or only NPT?
Threaded fittings sold into the US are NPT. Australian plumbing is predominantly BSP, and the two are not interchangeable even where the nominal size matches — the thread angle and pitch differ. For any threaded item, confirm the standard when you send your list. Non-threaded parts (unions with O-ring seals, cartridges, gaskets) are unaffected.
Your pumps are built for the US market. Will the parts fit equipment running on 240V/50Hz?
Mechanical parts — O-rings, seals, impellers, diffusers, filter cartridges, valve components, baskets — are identical regardless of supply voltage, and fit the same way here as they do in the US. Motors and motor-driven assemblies are the exception: Australian supply is 230–240V 50Hz against 115/230V 60Hz in the US, and a 60Hz motor run on 50Hz turns roughly 17% slower, which changes flow rate and can overheat the winding. We do not substitute motors across frequencies. Tell us the part number and we will say plainly whether it is frequency-independent.
How does freight and lead time work to Australia?
Sea freight from Ningbo or Shanghai to Sydney, Melbourne and Brisbane typically runs 14–21 days port to port, Perth and Auckland slightly longer, plus production time. We quote FOB or CIF. Air freight is available for samples and urgent service parts.
POOLPOINT is an independent manufacturer. Not affiliated with, sponsored by or endorsed by SuperPro. The SuperPro name and OEM numbers are used to identify fitment only.