Brand: Maytronics
Replacement parts compatible with Maytronics
87 parts
- Matched to OEM specs
- Batch-tested quality
- Verified cross-references
POOLPOINT is an independent manufacturer. Not affiliated with, endorsed by or sponsored by Maytronics. Brand names indicate fitment only.
Maytronics OEM prefix guide
Shop Maytronics parts by category
87 parts
View all 87
Fits Maytronics
Cleaner Track Set, Gray, Compatible with Maytronics Dolphin Cleaners
Fits Maytronics
Guide Wheel, White, for Dolphin Robotic Pool Cleaners, Compatible with Maytronics
Fits Maytronics
Handle Float for Dolphin 3001 HD, Compatible with Maytronics
Fits Maytronics
Bottom Lid Assembly with Support, 12-1/2 x 9-1/4-Inch, Compatible with Maytronics
Fits Maytronics
Combination Brush for Robotic Pool Cleaners, Gray, Compatible with Maytronics
Fits Maytronics
Filter Bag Clip Set for Dolphin Cleaners, Compatible with Maytronics
Fits Maytronics
Power Supply, 180W, for Wi-Fi Pool Cleaner Models, Compatible with Maytronics Dolphin
Fits Maytronics
Bottom Lid Assembly, Compatible with Maytronics Dolphin Pool Cleaners
Fits Maytronics
Right Side Panel for Nautilus Plus Robotic Pool Cleaner, Compatible with Maytronics
Fits Maytronics
KA50x16 Screw for Dolphin Robotic Pool Cleaners, Replacement for Maytronics
Fits Maytronics
Motor Assembly, 3-Hour Diagnostic CB, for Old Style Nautilus Cleaners
Fits Maytronics
Caddy Pillar Mount, Black, Compatible with Maytronics Dolphin Cleaners
Fits Maytronics
Motor Unit, Black, for Dolphin Nautilus CC Plus and M200 Cleaners
Fits Maytronics
Handle Assembly for Dolphin Deluxe 4 and Deluxe 5, Compatible with Maytronics
Fits Maytronics
Side Panel Float for E55 and Liberty Cleaners, Compatible with Maytronics
Fits Maytronics
Tune-Up Kit for Dolphin Nautilus CC Plus, Compatible with Maytronics
Fits Maytronics
Cleaner Cable with Swivel, 60-Foot, 2-Wire, Compatible with Maytronics Dolphin
Fits Maytronics
Power Supply Socket, Compatible with Maytronics Robotic Pool Cleaners
Fits Maytronics
Guide Wheel and Pulley Gear Kit for Dolphin Cleaner, Compatible with Maytronics
Sourcing Maytronics-compatible parts in bulk
An aftermarket Maytronics-compatible part is manufactured to the same critical dimensions as the original but is not made by Maytronics. We check every part against an OEM sample for thread pitch, port geometry and sealing surfaces before tooling is approved, so it installs without modification.
Maytronics numbers typically carry prefixes such as MAY — the number is usually molded into the part or printed on the equipment label. Enter it above to find cross-referenced replacements.
Before committing to a container, distributors should confirm fitment by OEM number, equipment model, and thread or port size. We supply photos, dimensional drawings and, on key parts, 3D models — plus samples for validation ahead of bulk production.
FAQ
Are these genuine Maytronics parts?
No. We manufacture compatible aftermarket replacements. Maytronics OEM numbers are listed to identify fitment only, and we are not affiliated with Maytronics.
Do you supply BSP threads or only NPT?
Threaded fittings sold into the US are NPT. Australian plumbing is predominantly BSP, and the two are not interchangeable even where the nominal size matches — the thread angle and pitch differ. For any threaded item, confirm the standard when you send your list. Non-threaded parts (unions with O-ring seals, cartridges, gaskets) are unaffected.
Your pumps are built for the US market. Will the parts fit equipment running on 240V/50Hz?
Mechanical parts — O-rings, seals, impellers, diffusers, filter cartridges, valve components, baskets — are identical regardless of supply voltage, and fit the same way here as they do in the US. Motors and motor-driven assemblies are the exception: Australian supply is 230–240V 50Hz against 115/230V 60Hz in the US, and a 60Hz motor run on 50Hz turns roughly 17% slower, which changes flow rate and can overheat the winding. We do not substitute motors across frequencies. Tell us the part number and we will say plainly whether it is frequency-independent.
How does freight and lead time work to Australia?
Sea freight from Ningbo or Shanghai to Sydney, Melbourne and Brisbane typically runs 14–21 days port to port, Perth and Auckland slightly longer, plus production time. We quote FOB or CIF. Air freight is available for samples and urgent service parts.
POOLPOINT is an independent manufacturer. Not affiliated with, sponsored by or endorsed by Maytronics. The Maytronics name and OEM numbers are used to identify fitment only.